- Speaker enclosure design software how to#
- Speaker enclosure design software driver#
- Speaker enclosure design software full#
- Speaker enclosure design software software#
- Speaker enclosure design software trial#
In our case, Q tc of 0.7 was achived at 5.6 liters.
Speaker enclosure design software trial#
By trial and error you will reach the desired Q tc. Go to the Enclosure tab, lower or increase the volume, then head back to Transfer Function and plot again. Supposedly, your goal is a Butterworth 0.7 Q tc, you can do 2 things, depending on the situation : We are interested in the Q tc value. Seems like a 10 liter enclosure yields a Q tc of 0.56. At the end of each line there is an (S) or a (V), which stands for sealed or vented. Furthermore, there is some important information in the corner. Then, go to Transfer Functions tab and click plot.Īfter you click the plot button, you see the modeled frequency response. Therefore, you can adopt the trial and error way.įirst of all, enter a volume that seem reasonable for that particular speaker (something lower than V as). While that will give us a direct answer, most people can’t be bothered to calculate. As for the volume, you can calculate it by choosing a desired Q tc (more details here). But, if you think you enclosure will be a solid one in terms of air tightness, go for 15. When the sealed enclosure is checked, you can alter 2 factors :įor box losses I suggest to go for 7. Therefore, we will go only for the popular choices : SoundEasy enclosure design for sealed and bass reflex. In conclusion, there many types of enclosures to choose from, but let’s keep the article to a decent length.
PR / Port Q p – The losses of the port or passive radiator.Radiator F p – Resonant frequency of the passive radiator.Radiator V ap – The equivalent compliance in liters of the passive radiator (like V as for the active speaker).Number of radiators – The number of radiators in a passive radiator enclosure.Front box Q b – Box losses of the front chamber.Front box F b – Tuning frequency of the front chamber.Only available in dual chamber enclosures, like bandpass. Front box V b – The volume of the front chamber.Lower values (3-4) suggest a leaky enclosure and should be avoided. But, if you plan to use a lot of silicone sealant, and make the box as air tight as possible, you can go with a Q b of 15. Normally you would select a medium value (like 7). Rear box F b – The tuning frequency of the box.When the enclosure has a single chamber, it is referred to as the rear chamber. Rear box V b– The volume of the box (sealed, bass reflex, etc).Here is a brief explanation of the more common ones : The parameters on the right side become available, depending on which type of enclosure you check (on the left side). BP3 is a variation of 6th order bandpass.You got the obvious ones : Sealed, Vented / Ported, Passive radiator, Transmission line, Horn.If you find yourself at this stage, you can proceed to Enclosure Tools -> Enclosure Design.ĭepending on which type of enclosure you choose, the parameters to the right will become available.
Speaker enclosure design software driver#
After you completed all the steps mentioned above, the driver editor should look like this :Īs you can see, I have not completed all the parameters. As a result, I don’t have to do all those measurements again.
It’s the same driver used in the impedance measurement and T/S parameter extraction article. SoundEasy enclosure designįor this demonstration, we are going to use the SEAS CA 18 RNX (Amazon affiliate paid link). So, if you want to input them (maybe using the spec sheet of your driver), be my guest. In the driver editor, there are more parameters, but they are optional. As an alternative, you can input them manually, if you measured them using another device (or import them, if the format is supported).
Speaker enclosure design software full#
This means both the Basic T/S and Full T/S.
Speaker enclosure design software software#
Making a SoundEasy enclosure design will most certainly not be as intuitive as the other enclosure modeling software out there.
Speaker enclosure design software how to#
How to design an enclosure using SoundEasy?
0 kommentar(er)
